Blog Contact

SAG Mill Liner Removal And Installation Safety Procedures

SAG mill liner replacement is a high-risk maintenance activity involving heavy components, stored energy, restricted access, suspended loads, and changing ground conditions inside a rotating mill. A disciplined method is essential because a liner can weigh hundreds or thousands of kilograms, while the work area may combine steel structures, hydraulic equipment, water, grinding media, and poor visibility.

For Australian mine operators, the task must fit the site’s safety management system, isolation rules, permit process, and applicable state or territory requirements. Whether the mill is operating in the Pilbara, near Kalgoorlie, or at a processing operation in Queensland, the safest result comes from detailed planning, competent crews, suitable tooling, and clear communication from shutdown preparation through recommissioning.

Why Liner Work Demands Strict Control

SAG mill liners protect the shell from impact and abrasion while helping lift and tumble the ore charge. During replacement, workers may enter the mill to remove worn lifter bars, discharge plates, grates, pulp lifters, or shell liners. The condition of these components can be unpredictable. Cracked bolts, distorted plates, trapped rocks, and weakened backing materials may release without warning.

The mill must be treated as a confined and hazardous work environment, even when local rules classify the task differently. There may be limited access, difficult evacuation routes, heat, dust, noise, residual slurry, and reduced lighting. A risk assessment should address falls, crush points, dropped objects, manual handling, atmospheric conditions, and interactions between workers and mobile or lifting equipment.

A properly engineered liner handling system reduces exposure to these hazards. Specialist liner handlers, reline machines, hydraulic removal tools, purpose-built lifting beams, and remote-controlled equipment can keep people away from suspended loads and pinch points. Project owners assessing plant upgrades can review integrated processing solutions alongside maintenance requirements so that safe access and maintainability are considered during plant design.

Planning The Shutdown And Work Method

The work should begin with a site-specific job safety analysis, task risk assessment, or safe work method statement. It should define the mill configuration, liner type, removal sequence, installation pattern, crew roles, communication method, equipment limits, emergency arrangements, and stop-work conditions. Manufacturer instructions and the latest mill drawings must be available at the work front.

Isolation is more than stopping the mill. The electrical supply, hydraulic systems, inching drive, lubrication systems, feed conveyors, reclaim equipment, water lines, compressed air, and other connected systems must be identified and isolated. The mill should be prevented from rotating through approved mechanical restraint or locking arrangements. Stored energy in hydraulic cylinders, suspended components, trapped pressure, and elevated equipment must be released or controlled.

Australian operations commonly use permit-to-work systems, isolation registers, and verification by an authorised person. On a FIFO roster in Western Australia, the handover between crews deserves particular attention. The incoming team must understand which liners have been removed, what equipment remains suspended, which isolations are active, and whether any temporary structures or access platforms have changed.

Pre-Job Controls And Equipment Checks

Before the first liner is disturbed, the supervisor should inspect the work area and confirm that the planned equipment matches the load, reach, access, and ground conditions. The crew should conduct a pre-start briefing at the mill, not only in a crib room, so hazards can be seen and discussed. Every worker needs to know who may authorise movement and which radio or hand signals apply.

The following controls should be verified before entry:

Lifting accessories must be selected for the actual load and lifting geometry, not an estimated average weight. A competent person should check for damaged hooks, stretched links, bent beams, worn attachment points, and hydraulic leaks. In Australia, lifting equipment and dogging or rigging activities must align with site rules and relevant workplace safety requirements, with licensed personnel used where the task calls for them.

Safe Removal Of Worn Liners

Removal should follow a controlled sequence that prevents uncontrolled release. Workers should stand clear while hydraulic tools loosen bolts or push plates from the shell. If a liner is seized, the team should stop and reassess rather than increase force without engineering approval. Heat, impact tools, or cutting may introduce additional fire, fume, vibration, and structural hazards.

A liner must be supported before its final fasteners are removed. The lifting device should be connected to designated lifting points, the load stabilised, and the area below cleared. No person should pass beneath a suspended liner or place hands between a plate and the shell. Tag lines may help control rotation, but they should never be wrapped around hands or used where they could become caught.

The removal sequence also needs to protect the mill shell and adjacent components. Unplanned removal of several neighbouring liners can alter load distribution or expose unsupported areas. Workers should keep track of removed parts and maintain a clear route for transport. At large iron ore operations near Port Hedland or Newman, separation between the reline crew, crane operations, and haulage routes is especially important because shutdown traffic can remain heavy around the processing plant.

Installation Controls And Liner Placement

Before installation, the shell should be cleaned and inspected for cracks, corrosion, damaged bolt holes, deformation, and remnants of old backing material. Any defect outside the approved repair scope must be reported and assessed. Correct liner identification is critical: lifter bars, shell plates, grate panels, and pulp lifters may look similar but have different locations, orientation, and fastening requirements.

Safe installation depends on controlling the component from pickup to final tightening. The liner should be lifted using approved points and aligned with the correct shell location before workers approach for fastening. Hands and feet must remain outside pinch zones. Workers should use push-pull tools or alignment aids rather than trying to guide a heavy plate manually.

Installation checks should include:

Torque equipment should be calibrated, suitable for the fastener size, and used according to the manufacturer’s instructions. Hydraulic tensioning or torque reaction can create sudden movement, so reaction points must be planned before force is applied. The supervisor should maintain a live installation record to prevent missed bolts or duplicate work when crews change during long shutdowns.

Managing Confined Space And Human Factors

Mill entry controls should address access, egress, communication, lighting, atmospheric testing, and rescue. If the risk assessment identifies a confined space, the site’s confined-space permit and standby arrangements must be followed. Gas testing may be needed where process residues, combustion equipment, cleaning chemicals, or poor ventilation could affect air quality.

Fatigue is a practical concern during extended shutdowns. Crews may work nights, travel long distances, or operate under production pressure to return the plant to service. Supervisors should manage breaks, rotate physically demanding tasks, and stop work when visibility, heat, dust, or alertness deteriorates. Clear bilingual or visual communication may be needed on diverse crews, particularly where a single misunderstood signal could move a suspended load.

Personal protective equipment supports the control system but does not replace it. Typical requirements include a hard hat, safety footwear, eye protection, gloves suited to the task, hearing protection, high-visibility clothing, and fall-arrest equipment where applicable. Respiratory protection should be selected from exposure information and fit-tested before use.

Recommissioning And Final Verification

After all liners are installed, the mill interior should be inspected systematically. Tools, lifting accessories, temporary restraints, loose bolts, packaging, timber, and debris must be removed. The team should verify that grates and pulp lifters are correctly secured, discharge paths are clear, and no person remains inside or near a danger zone.

Isolation removal must be controlled by the authorised process. Every worker should remove their own personal lock unless the site procedure provides a formally managed alternative. Guards and covers must be reinstated before testing. A controlled rotation or inching check can identify abnormal contact, interference, or unusual noise before the mill returns to full operation.

The completed record should include torque results, inspection findings, replaced components, outstanding defects, and photographs where useful. A post-job review can capture lessons about liner wear, access, tooling, and crew coordination. Those findings help improve the next shutdown and may also indicate changes needed in mill operating conditions, liner design, or maintenance intervals.

A safe reline is achieved through preparation, engineered handling, verified isolation, and consistent discipline at every movement. Mine owners, maintenance contractors, and processing specialists should align the work method with the mill manufacturer, site leadership, and local legal requirements before the shutdown begins. For support with mineral processing equipment, plant engineering, and maintenance-focused project planning, contact Lozova.org to discuss a solution suited to the ore, mill configuration, and operating conditions.